GE Profile · 24-inch category · Sources reviewed 2026-09-14
GE Profile PDT795SBVTS cabinet opening requirements
Manufacturer-sourced opening requirements and body dimensions for the GE Profile PDT795SBVTS, with the record's status in the lookup. Every figure links to the document it was read from; “Not verified” means no document established it.
Sources reviewed 2026-09-14. A manual review compared the linked documents. A match in the lookup is a dimensional candidate for an installer to confirm, never a guarantee.
Cabinet opening requirements
| Measurement | Published requirement |
|---|---|
| Minimum opening height | 33 1/2 in |
| Maximum opening height | 34 3/4 in |
| Minimum opening width | 24 in |
| Maximum opening width | Not verified |
| Minimum opening depth | 24 in |
| Front clearance | 27 1/2 in |
| Corner clearance | Not verified |
Appliance body dimensions
Body dimensions describe the machine, not the hole it needs. They never substitute for the opening requirement above.
Installation notes from the review
- Keep plumbing and electrical services inside the shaded area in the installation drawing; the remaining rear wall must be clear.
- Compare the finished floor inside the opening with the room floor before planning removal or replacement.
Published features
- Sound rating
- 39 dBA
- Place settings
- 16
- Racks
- 3
- Drying system
- Twin Turbo Dry Boost™
- Annual energy
- 240 kWh/year
- Connectivity
- Built-In
Manufacturer specifications, checked September 20, 2026. Annual energy is a published estimate; sound ratings and drying names are not our test results.
Questions people ask about the PDT795SBVTS
The answers come only from the manufacturer documents linked on this page and the lookup's three outcomes.
What cabinet opening does the GE Profile PDT795SBVTS need?
The reviewed manufacturer document lists a minimum cabinet opening of 33 1/2 in high, 24 in wide and 24 in deep for the GE Profile PDT795SBVTS, with a maximum opening height of 34 3/4 in. Each figure links to its source in the table on this page. Its sources were reviewed on 2026-09-14.
Is the PDT795SBVTS a standard 24-inch dishwasher?
GE Profile places the PDT795SBVTS in the 24-inch category. That label describes the cabinet class, not the cutout: the reviewed minimum opening width is 24 in, and the appliance body is 23 3/4 in wide. Use the opening requirement, never the label, when you compare it with your cabinet.
Will the PDT795SBVTS fit my opening?
Only your measurements can answer that. Enter the opening's height, width and depth in the lookup; the PDT795SBVTS comes back as a dimensional candidate, an installer-review item or outside the published requirements. None of the three outcomes is a fit guarantee: mounting, utilities, floor level, trim, panel weight and door swing stay with the installer.
How tall is the PDT795SBVTS, and is that the opening height?
The manufacturer lists the PDT795SBVTS appliance body at 34 in high. The body height is not the opening requirement: the minimum opening height on record is 33 1/2 in and the maximum is 34 3/4 in. Measure from the finished floor to the counter underside at several points and use the smallest reading.
Why is the PDT795SBVTS held for installer review?
It carries installation notes from the review. Keep plumbing and electrical services inside the shaded area in the installation drawing; the remaining rear wall must be clear. Compare the finished floor inside the opening with the room floor before planning removal or replacement. The gate stays visible on this page until the evidence resolves.
Manufacturer documents
This is a document-based research record, not a physical installation test or a fit guarantee. Unknowns and source conflicts remain part of the decision.
Check your opening dimensions →
Exact-model retailer links
Resolve the status above before ordering. Confirm stock, delivery, installation service and final cost with the retailer. Links are ordered by retailer name, and commissions never change the dimensional checks.
All dishwasher records · How the research works · Corrections or a newer manufacturer drawing? Send us the model and source.